Testing the power supply
- Connect the tester to the power supply.
- Switch the power supply on.
- If the tester light is on, proceed to test the cable.
- If the tester light is off, check the power socket and AC cable. If they are working, then replace the power supply and proceed to test the cable.
Also, how do I test my pool cleaner power supply?
In this way, how do you test a dolphin power supply?
TEST 5D – Set the meter to 200 DC and check that the Dolphin Cable is attached to the Power Supply. TURN ON THE POWER SUPPLY. Then place the meter probes into the plug on the motor end of the Cable. If the meter shows 29V, you are getting power to the motor.
How do you replace climbing rings on a dolphin pool cleaner?
How do I fix my Nautilus Dolphin?
Can I plug my dolphin into an extension cord?
Amazon.com: Customer Questions & Answers. Dolphin Nautilus Automatic Robotic Pool Cleaner with Dual Filter Cartridges, Two Scrubbing Brushes… Dolphin does not recommend an extension cord.
How do I fix my Dolphin s300?
How do I test dolphin cable?
Testing the cable
- Unscrew the two screws holding the front top cover in place, and remove the cover. …
- Open the clip that holds the cable in place and remove the cable.
- Remove the cable from the motor unit, and unplug the cable.
- Connect the cable to the power supply (1) and tester (2).
- Switch the power supply on.
How long do pool robots last?
Can Maytronics power supply get wet?
The power supply is water resistant but not waterproof. Please cover the power supply if inclement weather approaches. Do not leave the power supply in standing water as this will damage the internal components.
How long do dolphin pool cleaners last?
Generally, you can expect at least 5 years‘ service from your quality robotic pool cleaner. The more expensive units are generally better quality – you do get what you pay for.
Why is my dolphin pool cleaner not climbing walls?
My Dolphin Won’t Climb Walls / Gets Stuck
Clean filters: The Dolphin’s filters may be clogged and need to be cleaned. Make sure you clean these filters after each use. Do not allow filters to dry out before cleaning. Deeper cleaning of the filters is also highly encouraged and may be required occasionally.
Why does my dolphin keep turning off?
Most likely – a clogged impeller. This is common, easy to fix, and the video below shows you how to unscrew the cover to get to your impeller. My impeller was clear of debris, but REALLY difficult to spin by hand, so I figured my motor was bad, and I was right.
How long is a dolphin pool cleaner cycle?
Each cleaning cycle is 2 hours. If it doesn’t finish cleaning in one cycle, you’ll have to manually restart it. All of that is done with a few buttons on the power supply. Like other cleaning robots with smart navigation, it will take a few cycles for it to map out the most efficient path for your pool.
Why won’t my dolphin pool cleaner climb walls?
My Dolphin Won’t Climb Walls / Gets Stuck
Clean filters: The Dolphin’s filters may be clogged and need to be cleaned. Make sure you clean these filters after each use. Do not allow filters to dry out before cleaning. Deeper cleaning of the filters is also highly encouraged and may be required occasionally.
Can Dolphin power supply get wet?
The power supply is water resistant but not waterproof. Please cover the power supply if inclement weather approaches. Do not leave the power supply in standing water as this will damage the internal components.
Why is my pool robot not working?
If your robotic pool cleaner stops moving, check the power cord. It may not be plugged in properly or there may be a problem with the power supply. Check the power supply to make sure the indicator light is on. If it is and the pool cleaner is still not moving, then the problem lies with the cleaner.
How do I fix my dolphin pool cleaner?
Troubleshooting
- Check that the power supply cable is plugged properly into the power supply socket. Check power to the socket and reconnect Pool Cleaner.
- Ensure the power outlet is functioning properly and that it has not tripped the breaker in the fuse box.
- Turn the power supply off. …
- Unplug the power supply.
Can I leave my robotic pool cleaner in the pool?
Cleaners aren’t meant to stay in the pool 24/7. This is true for all cleaners. Pressure side cleaners run on a schedule every day so why take it out? Leaving the cleaner in the pool 24/7 increases its exposure to corrosive chemicals in the water, such as chlorine or shock.
How do I reset my dolphin power supply?
Check that the power supply is plugged in and turned ON. Check that the power cable is securely connected all the way into the power supply. Turn the power supply OFF. Wait 30 seconds, then turn it back on.
How do you troubleshoot a dolphin pool cleaner?
Troubleshooting
- Check that the power supply cable is plugged properly into the power supply socket. Check power to the socket and reconnect Pool Cleaner.
- Ensure the power outlet is functioning properly and that it has not tripped the breaker in the fuse box.
- Turn the power supply off. …
- Unplug the power supply.
Should I leave my pool robot in pool?
You can swim while your bot cleans the pool, but it’s better not to. Swimming churns up the water. If the machine is in the water at the time, the current will buffet it, making it harder for it to complete its work. It’ll have to work harder to cover the same ground.
How long is Maytronics warranty?
How do I turn on my Maytronics pool cleaner?
TURN POWER ON – Press the ON/OFF switch on the Power Supply. The Cleaner will start to operate. Note: Four LEDs will light up in the corners of the switch indicating that the power is on.