It could be a bad drive, over voltage, under voltage, drive over heating, ect. You could eliminate it being a control problem by unplugging the control cable on the motor, and manually running it. If it does not do it anymore then it is a control issue.
Beside this, how do I reset my Pentair pool filter?
Also, how do I reset my Pentair easy touch?
How do I turn on Pentair Intelliflo variable speed pump?
How do I program my Pentair Intelliflo VSF?
Why is my pool pump not working?
It could be something blocking it, a dirty pool filter, or too much air in the system. If there’s something blocking your pump’s suction, check your filter gauge. If it’s 10psi above the normal reading, clean your filter. This will reduce pressure and reset your pump’s flow.
How do you clear an alarm on a Pentair pool pump?
In the event of an alarm: The alarm light ” ” will illuminate and all control panel buttons will be disabled until the alarm is cleared. Pressing the Reset button will clear the alarm once the fault condition has been resolved.
How can you tell if your pool filter is not working?
There are ways to tell if the swimming pool filter is bad. If the water turns cloudy, then you know that your filter is not functioning properly. Leaking multi-port valves, broken or bad laterals, valve failure, tank failure, and pressure issues are some of the other indicators that the pool filter is bad.
How do you prime a Pentair Intelliflo pump?
How To Prime Your Pentair Pool Pump
- Turn off power to pump (switch and breaker)
- Using black 3 way valve, turn off Skimmer (main drain on only)
- Remove pump lid.
- Fill pump with water all the way to top.
- Put pump lid back on.
- Turn on Pump.
How do I reset my Pentair pool timer?
How to Set the Date/Time on the Pentair Intelliflo
- From the home screen, press the “Menu” button.
- Use the Up or Down Arrows to cycle to “Settings”
- Press “Select”
- Cycle to “Date/Time”
- Press Select.
- You will see the factory default Date, press “Select” again to edit.
How does Pentair freeze protection work?
The system detects all devices that have Freeze Protection ON, and activates the device to stop the pipes from freezing. If freeze protec- tion is only applied to one body of water. Note: If the pool or spa is running a schedule or operated manually, this will override freeze protection.
How do you reset pool pump after power outage?
How to “restart” your pool once power is restored
- Remove the pool cover and check for debris. …
- Close any drain plugs or valves you may have opened during the power outage.
- Turn the breakers back on and prime the pool pump by adding water to the pot, replace the lid and turn the pool pump on.
Why does my Pentair pump keep shutting off?
Overheating. For safety reasons, many pool pumps are designed to shut off automatically if they begin to overheat. The mechanisms that perform this task are known as thermal overload switches. If your pump continues to shut off, it could mean that the thermal overload switches are going bad.
How do you reset the time on a Pentair pool pump?
How do you troubleshoot a pool filter?
Here are two ways to check if your filter is working:
- #1. Add dirt to your pool skimmer. …
- #2. Use your pool vacuum to test for filter issues. …
- True Grit. This is the most common issue associated with sand or debris floating back into the pool after it’s been sucked up by the filter. …
- Too High of Pressure. …
- Too Low of Pressure.
Why does my pool pump keep turning on and off?
If you have a new pump or pool, your pump might be wired incorrectly or loosely! In the case your pump turns off a few seconds after turning it on you might even have a bad capacitor. Capacitors regulate the amount of power the pump gets and can go bad with age.
How many hours should I run my variable speed pool pump?
However, it is important to note that a variable speed pool pump should ideally be running 24 hours a day to ensure proper and optimal water circulation. When your pool pump is not running, the water is sitting stagnant in your pool allowing bacteria to survive and grow.
How do you unlock Pentair Intelliflo?
Press and hold all of the four Speed buttons simultaneously for four (or more) seconds. Power off the pump, wait a few seconds, power it back on.
How do I reset the schedule on my Pentair Intelliflo pump?
Is there a reset button on a Pentair pool pump?
How do I reset my Pentair Intelliflo variable speed pump?
To reset the pump to the factory default settings:
- Ensure that the pump is powered on and the green power LED is on.
- Press the Stop button to stop the pump.
- Press and hold all of the four Speed buttons simultaneously for four seconds. Power off the drive.
Why does my pool pump shut off randomly?
For safety reasons many pool pumps are designed to shut off if they begin to overheat. The pump uses thermal overload switches so if your pump keeps shutting off it could be because these switches are going bad. We don’t recommend troubleshooting an overheating pool pump without a professional.
How do I reset my Pentair Intelliflo VSF?
To reset the pump to the factory default settings:
- Ensure that the pump is powered on and the green power LED is on.
- Press the Stop button to stop the pump.
- Press and hold all of the four Speed buttons simultaneously for four seconds. Power off the drive.
Why does my pump keep turning off?
A blockage in the water supply piping.
For example, a clogged or nearly clogged water filter can cause the pump control to cycle on and off rapidly. This is because the blockage causes water pressure (between the pump and the filter) to rise very rapidly when the pump turns on.
How do I reset my Pentair variable speed pump?
Where are Pentair pool pumps manufactured?
Our manufacturing plant, located in St. Paul, Minneapolis, USA, produces products for fluid processing, respiratory, membrane, blood line and systems.
Should your pool pump run all the time?
Although it’s generally recommended that all the pool water undergo filtration every 24 hours, the pump does not need to run all the time. A proactive, productive and energy-saving maintenance activity is to remove the debris floating on the pool surface with a hand-held skimmer.
How do I program my Intelliflo 2 VST pump?
What does pool pump overcurrent mean?
I found this when searching for information on Intelliflo overcurrent alarms: Over current: Indicated that the drive is overloaded or the motor has an electrical problem. The drive will restart 20 seconds after the over current condition clears.