If you can identify an obstruction you can remove the object and then run your Dolphin again. If the Dolphin starts and continues to operate as per normal the the obstruction was the cause of the robotic pool cleaner not moving.
Similarly, how do I turn on my Maytronics pool cleaner?
TURN POWER ON – Press the ON/OFF switch on the Power Supply. The Cleaner will start to operate. Note: Four LEDs will light up in the corners of the switch indicating that the power is on.
Beside this, how do I fix my dolphin pool cleaner?
Why won’t my dolphin pool cleaner climb walls?
My Dolphin Won’t Climb Walls / Gets Stuck
Clean filters: The Dolphin’s filters may be clogged and need to be cleaned. Make sure you clean these filters after each use. Do not allow filters to dry out before cleaning. Deeper cleaning of the filters is also highly encouraged and may be required occasionally.
How long is Maytronics warranty?
Maytronics warrants that your Premier Dolphin pool cleaner will be free from defects in material and workmanship for 3 years. To prove how serious we are about delivering the best-in-class high performance robot, the Dolphin Premier is backed by the very best warranty in the industry.
How do you test a Maytronics power supply?
Testing the power supply
- Connect the tester to the power supply.
- Switch the power supply on.
- If the tester light is on, proceed to test the cable.
- If the tester light is off, check the power socket and AC cable. If they are working, then replace the power supply and proceed to test the cable.
Why does the creepy stop working?
The most common cause for a Kreepy to stop working is clogged filter sand. This is easy to diagnose because whenever you backwash the pool filter, you’ll find that the Kreepy works like a bomb for 10 minutes. Then it gets sluggish and slows down or stops again.
Why is my pool cleaner not moving?
When a suction cleaner is sluggish or slow, it’s usually a clogged pump basket or dirty filter that is to blame. Other problems include holes in the cleaner hose, sucking air into the hose, or the filter pump could be drawing in air, reducing water-flow volume.
How do you test a dolphin pool cleaner?
How do I get my pool vacuum to work?
Why is my pool robot not working?
If your robotic pool cleaner stops moving, check the power cord. It may not be plugged in properly or there may be a problem with the power supply. Check the power supply to make sure the indicator light is on. If it is and the pool cleaner is still not moving, then the problem lies with the cleaner.
Why is my zodiac pool cleaner not working?
Check the suction flow using your pool pulse. Check the AD valve. Check the pool cleaner hose for any air leaks and. Check the diaphragm in your Zodiac pool cleaner.
How do I fix my Nautilus dolphin?
How often should I run my dolphin pool cleaner?
Ideally, you need to run your robot pool cleaner daily or at least once a day if you’re always swimming in it. But if you don’t swim in it as much, run it at least once weekly or every two weeks. When you’re using a swimming pool cover all the time, you may wash your pool monthly.
How do I reset my dolphin?
Information
- Press and hold “Blue” and “Call” buttons to cold boot the Dolphin.
- Upon cold boot, when the display returns, type: 1277.
- A little menu will appear showing the reset options. Choose the top option by pressing the number ‘1’ on the keypad.
- A prompt will appear asking for confirmation.
How do you test a dolphin power supply?
Why is my Polaris floating?
Leaks in the Polaris hose cause the cleaner to lose pressure, allowing it to float above the pool bottom. To check for leaks, turn the system on and pull the hose out of the water one section at a time, looking for bubbles or trickles of water.
How do you replace parts in dolphin pool cleaner?
Why is my pool cleaner not working?
When a suction cleaner is sluggish or slow, it’s usually a clogged pump basket or dirty filter that is to blame. Other problems include holes in the cleaner hose, sucking air into the hose, or the filter pump could be drawing in air, reducing water-flow volume.
How long do pool robots last?
How do I get air out of my pool pump?
How do I troubleshoot Maytronics dolphin?
Troubleshooting
- Check that the power supply cable is plugged properly into the power supply socket. Check power to the socket and reconnect Pool Cleaner.
- Ensure the power outlet is functioning properly and that it has not tripped the breaker in the fuse box.
- Turn the power supply off. …
- Unplug the power supply.
Why does my pool cleaner stopped working?
When a suction cleaner is sluggish or slow, it’s usually a clogged pump basket or dirty filter that is to blame. Other problems include holes in the cleaner hose, sucking air into the hose, or the filter pump could be drawing in air, reducing water-flow volume.
How do I test dolphin cable?
Grip the cable firmly and pull it out of the socket. 4. Using a multimeter set to continuity, check the continuity of each wire. If continuity is good, replace the plug, it can only go in one way, and tighten the hold down nut.
Why is my automatic pool vacuum not moving?
If your robotic pool cleaner stops moving, check the power cord. It may not be plugged in properly or there may be a problem with the power supply. Check the power supply to make sure the indicator light is on. If it is and the pool cleaner is still not moving, then the problem lies with the cleaner.
How do you fix a pool cleaner?
How do you take apart a dolphin pool cleaner?
How do I adjust my dolphin pool cleaner?
To adjust the handle angle:
- Lay the handle down at an angle of 180º to the ground.
- Push the base of the arm into the body of the robot pool cleaner and slide it towards the rear of the robot pool cleaner until it clicks into the required position.
Why does my pool vacuum stay in one place?
The stronger the water flow, the more likely it is to get stuck in one place. You need some suction though or the pool won’t get cleaned properly. The easiest solution is a flow keeper valve. A flowkeeper valve is a valve that regulates the flow of water through the hose going to the cleaner.
Why does my pool cleaner get stuck?
The cleaner works by suction just like a regular vacuum cleaner, but instead of sucking in air, it sucks in water. A strainer catches all the debris and the water is recirculated. Now and then, the suction will become too strong and the cleaner will get stuck to the bottom of your swimming pool.
How do you troubleshoot a pool cleaner?
Summary of Pressure Pool Cleaner Troubleshooting
- Check the pump for adequate pressure.
- Check the wall strainer for blockages.
- Check the hose and swivels for tangles.
- Change the valve flow for more coverage of the pool.
- Replace waterlogged hose.
- Check tyres for wear and replace as required.
Can I use an extension cord with my dolphin pool cleaner?
Dolphin Nautilus Automatic Robotic Pool Cleaner with Dual Filter Cartridges, Two Scrubbing Brushes… Dolphin does not recommend an extension cord.
How do you troubleshoot a dolphin pool cleaner?
Troubleshooting
- Check that the power supply cable is plugged properly into the power supply socket. Check power to the socket and reconnect Pool Cleaner.
- Ensure the power outlet is functioning properly and that it has not tripped the breaker in the fuse box.
- Turn the power supply off. …
- Unplug the power supply.
How do you replace climbing rings on a dolphin pool cleaner?
Why does Polaris run on its side?
Can I leave my dolphin pool cleaner in the pool overnight?
While the unit can remain in the pool during use of the weekly timer function (if available on your model), we do not recommend leaving the cleaner in the pool for long extended periods of time.
Why is my aqua Critter not moving?
If your Pool Cleaner is not moving or is barely crawling it may be clogged with debris. This guide describes how to clear the the debris and check the operation of the Main Turbine that propels the pool cleaner.
Why is my robotic pool cleaner not moving?
If your robotic pool cleaner stops moving, check the power cord. It may not be plugged in properly or there may be a problem with the power supply. Check the power supply to make sure the indicator light is on. If it is and the pool cleaner is still not moving, then the problem lies with the cleaner.
Can you swim with a vacuum in the pool?
Increases Wear and Tear. You can swim while your bot cleans the pool, but it’s better not to. Swimming churns up the water. If the machine is in the water at the time, the current will buffet it, making it harder for it to complete its work.
How do I reset my dolphin power supply?
Check that the power supply is plugged in and turned ON. Check that the power cable is securely connected all the way into the power supply. Turn the power supply OFF. Wait 30 seconds, then turn it back on.
Where is the impeller on my dolphin pool cleaner?
Why can’t you use an extension cord with a dolphin pool cleaner?
Do not use an extension cord. In a wet deck environment the risk of stray voltage while small is signicant.
How do you use the Dolphin pool cleaner remote?
Using the remote control
- Press the On/Off button once. The remote control will start in manual direction control mode.
- Use the direction control arrows (see right) to control the movement of the robot around the pool.
- To exit the manual direction control mode, press the Manual/Automatic select button once only.
Why is my dolphin pool cleaner doing wheelies?
What causes automatic pool cleaners to flip or do wheelies? The water level in a pool is one of the most common causes for this problem. When the water level is too high, the water line is very close to the coping. So when the cleaner starts to climb the wall, it hits the coping and flips on to its back.
Can Dolphin power supply get wet?
The power supply is water resistant but not waterproof. Please cover the power supply if inclement weather approaches. Do not leave the power supply in standing water as this will damage the internal components. Do not allow the power supply to be submerged in the pool.
What to do when pool vacuum stops working?
First, if you find your pool cleaner not moving, check the cleaner’s hose to make certain it is strongly affixed to the suction-line in the skimmer. Additionally, if you find your pool vacuum not moving, check the hose segments to make certain there are no air-leaks where the hose sections meet together.