The task of replacing a pool pump motor can be difficult, but we’re here to make sure you get it done as quickly, easily, and successfully as possible. Make sure the power to the pump is turned off before beginning the replacement. Make sure you’ve got the correct tools to disassemble and reassemble the parts involved.
Correspondingly, how do you tell which Hayward pump I have?
Beginning with ‘SP’ followed by four numbers, sometimes ending with a suffix of numbers and letters, is how Hayward identifies most of their products. After you’ve found and copied down this number enter it into Inyo’s “Keyword or Part #” search, the result will be the direct replacement for your pump motor.
In respect to this, how much is a pool pump motor?
Pool Pump or Motor Replacement
Merely replacing the motor is less costly than replacing the whole pool pump. A DIY motor replacement costs around $25 to $200, while hiring a professional can cost an additional $40 to $100.
How do I fix my pool pump motor?
What is a pool volute?
Length x width x depth x 7.5 = volume (in gallons)
Length times width gives the surface area of the pool. Multiplying that by the depth gives the volume in cubic feet. Since there are 7.5 gallons in each cubic foot, multiply the cubic feet of the pool by 7.5 to arrive at the volume of the pool, expressed in gallons.
How do you know if your pool pump motor is bad?
Your pump could be leaking water, or the bearings might need to be replaced instead of the entire motor. Screeching is also a sign that your motor bearings need to be replaced. These loud, often painful sounds could also be a sign of rust or oxidation, making it more difficult for the bearings to do their job.
What is the difference between a pool pump and a pool motor?
The pump’s shaft spins up to 3,450 revolutions per minute to turn the impeller to draw water from your pool and then push it through your filter and back to the pool. The motor is a cylindrical steel enclosure, usually black but sometimes gold or almond-colored, bolted to the back end of the wet end.
Is it worth fixing a pool pump?
When determining the magic number of replacement parts cost versus the cost of the whole pump, we generally suggest 60-75% as the standard. If the cost to repair is within or over this range, it is smarter to replace the pump. This way you have a brand new pump and warranty covering any mishaps down the line.
How do you replace a pool pump motor?
How do you fix a Pentair pump?
How can you tell if your pool pump is going bad?
Signs You Need Pool Pump Replacement
- Rumbling Sounds. An excessively-vibrating pump motor can create these rumbling sounds. …
- Grinding or Screeching Sounds. …
- Blowing Bubbles and Spitting Water. …
- Old Age. …
- Get a New Pool Pump Now to Keep Enjoying Safe Water.
Why does my pool pump turn on randomly?
Does your pump turn on at night by itself? It is doing so because the computer control has a freeze sensor. when the temperature drops below 36 degrees Fahrenheit, the system will turn on the pump. This is to prevent water from freezing in the pipes.
How do I reset my Pentair Intelliflo?
Resetting the pump to factory defaults
- Ensure that the pump is powered on and the green power LED is on.
- Press the Stop button to stop the pump.
- Press and hold all of the four Speed buttons simultaneously for four seconds. Power off the drive.
How do you remove the motor from a Pentair pool pump?
How long do pool pump motors last?
Most pool pump motors last at least 6-8 years, often longer. But that’s if you’re referring to magnetic drive pool motors, which are used in newer variable speed pumps.
How do you change pool pump motor?
How long should a Hayward pool pump motor last?
Why does my Pentair pump shut off?
Overheating. For safety reasons, many pool pumps are designed to shut off automatically if they begin to overheat. The mechanisms that perform this task are known as thermal overload switches. If your pump continues to shut off, it could mean that the thermal overload switches are going bad.
How do you replace a pool motor?
How do I reset my Pentair pool timer?
How to Set the Date/Time on the Pentair Intelliflo
- From the home screen, press the “Menu” button.
- Use the Up or Down Arrows to cycle to “Settings”
- Press “Select”
- Cycle to “Date/Time”
- Press Select.
- You will see the factory default Date, press “Select” again to edit.
How do you manually turn on a Pentair pool pump?
How do you replace pool pump motor bearings?
How do you remove impeller from pool pump motor?
By using a strap wrench, pool owners can gently loosen the impeller and make it easier to unthread. Depending on the model of the pump, the shaft may vary. Some pumps provide a slot on the end of the shaft to secure with a screwdriver. Often times, you can access the slot by removing the motor cap.
Can I replace a 1hp pool pump with a 1.5 HP?
So to answer the question, yes, you can replace your 1hp pool pump with a 1.5hp pool pump, but only if your situation calls for it. If you’ve determined that your current pump is too small for your pool, then we’ll suggest replacing it with a larger ECO pump like the Water TechniX Pump Alpha ECO.
How do you remove a Hayward pool pump motor?
Does a Pentair pool pump have a reset button?
Should your pool pump run all the time?
Although it’s generally recommended that all the pool water undergo filtration every 24 hours, the pump does not need to run all the time. A proactive, productive and energy-saving maintenance activity is to remove the debris floating on the pool surface with a hand-held skimmer.
When should I replace my pool pump motor?
Your pool pump should be replaced anywhere between 8 to 15 years depending on the quality, and a full replacement may cost over $800. Your pool pump is the “heart” of your swimming pool as it circulates water throughout, bringing water through the filtration and heating systems.
What are the parts of a pool pump motor?
So let’s break down the parts of a pump and see how they contribute to the overall functionality.
- The Housing. Inside a Pool Pump Housing. …
- Lid. …
- Strainer Basket. …
- Gaskets & Seals. …
- Seal Plate. …
- Motor. …
- Impeller. …
- Diffuser.
How do you rebuild a pool pump motor?
Do pool pumps lose power over time?
The pump is losing power.
Over time, older pumps can begin to deteriorate and lose power. In other cases, you might need to clean the filter or have it backwashed.
What does overcurrent mean on a pool pump?
Over Current
Indicated that the drive is overloaded or the motor has an electrical problem. The drive will restart 20 seconds after the over current condition clears.
How do I reset my IntelliFlo pool pump?
How can you tell how old a Hayward pool pump is?
How do I determine the age of a Hayward pool heater from the serial number? The 5th and 6th digits of the serial number of a Hayward heat pump pool heater are the year of manufacture, and the next two are the month.
How do you replace an above ground pool pump?
Where are Pentair pool pumps manufactured?
Our manufacturing plant, located in St. Paul, Minneapolis, USA, produces products for fluid processing, respiratory, membrane, blood line and systems. Our manufacturing plant located in Houston, TX, USA, produces products for industrial, pneumatic, fluid process, and hydraulic applications.
How do I test my pool pump motor?
How long do Pentair pumps last?
Pumps should last through the initially installed motor and perhaps as many as two or three replacement motors, usually 10-12 years. Modern pumps are made of hard plastic and will over time warp.
Can a Hayward pool pump overheat?
A pool pump can overheat in two ways: because of an electrical problem or friction. While electrically related failures are by far the most common cause for pump overheating, as we will discuss at length, there is also the potential for a friction fire to develop if a pump is starved for water.
What does impeller ring do?
Impeller wear rings are small plastic rings (10) that protect a misaligned impeller from rubbing, and must be installed before placing the Diffuser. TIP: Each horsepower motor is matched to a slightly different sized impeller, with a different part number.
How do you separate a pool pump motor and pump?
How do I know if I need a new pool pump?
Signs You Need Pool Pump Replacement
- Rumbling Sounds. An excessively-vibrating pump motor can create these rumbling sounds. …
- Grinding or Screeching Sounds. …
- Blowing Bubbles and Spitting Water. …
- Old Age. …
- Get a New Pool Pump Now to Keep Enjoying Safe Water.
What is the impeller on a pool pump?
Why is my pool pump leaking from the bottom?
In most cases, a leak underneath a pool pump is caused by a pressure-side leak. This is easily combated by inspecting the impeller housing o-ring, shaft seal and replacing any worn, cracked o-rings or seals. Before taking apart your pool pump, we recommend purchasing a go-kit.
Why does my Intelliflo pump keep shutting off?
It could be a bad drive, over voltage, under voltage, drive over heating, ect. You could eliminate it being a control problem by unplugging the control cable on the motor, and manually running it. If it does not do it anymore then it is a control issue.
How do I know what Hayward filter I have?
How do you replace a pool pump impeller?
How much does it cost to rebuild a pool pump motor?
A replacement motor is generally going to cost you in the neighborhood of $150 – $300 depending on the horsepower. Add another $15 – $30 for the absolutely necessary, non-negotiable new shaft seal.
How do you unlock Pentair Intelliflo?
TO UNLOCK THE PUMP:
Press and hold the “1” and Quick Clean buttons for atleast 3 seconds. “Enter Loc Code” will scroll across the screen.
How long does a pool pump motor usually last?
Most pool pump motors last at least 6-8 years, often longer. But that’s if you’re referring to magnetic drive pool motors, which are used in newer variable speed pumps.
How do I know what Hayward pump I have?
Model number is found on the dataplate located on the bottom right of the electrical cover on Hayward Heat Pro units.