How do I drain my Hayward pool water?

How to Drain A Pool with a Cartridge Filter

  1. Shut off the pump.
  2. Go to the back of the filter and unscrew the drain plug.
  3. Turn the pump back on and let the water run until it reaches the point where you want to drain the water out.
  4. Turn the pump back off and put the plug back into the drain plug.

>> Click to read more <<

Secondly, does backwash drain the pool?

Before You Drain Your Pool

Either pool draining methods will require a backwash hose. It is very important to direct your backwash hose toward to an area that won’t flood from all of the water flow. For most homes, this means draining into the driveway so water can roll down and then into the drains in the street.

Also question is, should pool main drain be open or closed? For proper water circulation, it is best to position the flap so that it is about 2/3 closed. This will allow for more flow through the main drain than through the skimmer, which will promote a “bottom-to-top” circulation throughout the pool.

In this regard, does backwashing remove water from pool?

Backwashing can result in a loss of water. While this is unavoidable, you can minimize the amount of water you lose by not overdoing the backwashing process. Keep a close eye on the colour of the water through the view glass and stop the minute it becomes clear.

Can you use pool pump to drain pool?

Never use your pool pump to try to drain the pool. Inevitably, you will pull air into your suction line, the pump will lose its prime, and you will damage or burn up your pump. Always rent or purchase a submersible pump to drain the pool.

How do you drain a pool without a main drain?

Because there is no main drain on most aboveground pools, you will only be able to lower the water to the bottom of the intake or skimmer, using your aboveground pool filter system. To drain an aboveground pools, either a). Use small submersible electric pump and garden hose, or b).

How do I empty my pool pump?

How do you drain an inground pool with a hose?

Put one end of your garden hose inside the port. Thread the hose to the back of your house. Attach the other end of the garden hose to a submersion pump and place the hose and pump in the deepest area of your pool, near the drain. The pool will begin to drain.

How do you drain a Hayward pool filter?

Can you drain a pool by backwashing?

It is not recommended to drain a swimming pool through the backwash valve. While sucking from the main drain and putting the water down the backwash line will work in some scenarios it puts your pool pump at risk of losing prime and running dry.

How does a pool drain work?

A pool’s so-called main drain is not actually a drain; that is, it is not used to drain the pool. Instead, it is an outlet, housing a pipe that runs to the pump, which sucks water through a skimmer, then through a filter, then through a heater (if you have one), and then back to the pool via multiple inlets.

How do I get the last 2 inches of water out of my pool?

Since both draining methods will not drain pool water to the last bit, you need to

  1. Use a wet vacuum to suck the stagnant water.
  2. Sweep the liquid into the drain.
  3. Remove the pool liner and flip it over somewhere your property to get rid of extra water.

Where is the pool main drain valve?

The main drains are usually located on the lowest point in the pool, so the entire pool surface slants toward them. Most of the dirt and debris that sinks exits the pool through these drains.

How do you drain a Hayward inground pool?

How to Drain the Pool with Hayward Pump?

  1. Water level. What is your groundwater level and where can you drain a large number of gallons? …
  2. Proximity. …
  3. The pump or tool. …
  4. First, you need to set It up. …
  5. Connect the hose pipe to sewer and pump. …
  6. Drop the pump in the shallow end. …
  7. Start draining the water.

What happens if pool water level is too high?

If the level is higher than that, it may slow or even stop debris from being pulled into the skimmer box through the plate or valve. This means that there will be floating debris left on your pool water surface as a result.

How do you drain an inground pool with a Hayward?

How to Drain the Pool with Hayward Pump?

  1. Water level. What is your groundwater level and where can you drain a large number of gallons? …
  2. Proximity. …
  3. The pump or tool. …
  4. First, you need to set It up. …
  5. Connect the hose pipe to sewer and pump. …
  6. Drop the pump in the shallow end. …
  7. Start draining the water.

How can I empty my pool without flooding my yard?

All you need is a medium-size water or vacuum pump.

  1. Unroll the pump’s intake hose so that it reaches the center of the pool (or as close to it as possible), and submerge it in the pool.
  2. Place the outlet hose so the exiting water doesn’t flood the area, but drains off away from the pool.
  3. Dry your hands thoroughly.

How long does it take to drain a pool with a pump?

between 8 and 14 hours

How do I let water out of my pool?

Leave a Comment