How to “restart” your pool once power is restored
- Remove the pool cover and check for debris. …
- Close any drain plugs or valves you may have opened during the power outage.
- Turn the breakers back on and prime the pool pump by adding water to the pot, replace the lid and turn the pool pump on.
Subsequently, why does my Intelliflo pump keep shutting off?
It could be a bad drive, over voltage, under voltage, drive over heating, ect. You could eliminate it being a control problem by unplugging the control cable on the motor, and manually running it. If it does not do it anymore then it is a control issue.
Consequently, how do I turn on my Pentair pool pump?
Why does my pool timer not work?
If power is reaching the clock, but the motor gears are not turning, that usually means either something is jammed in the gears (I once found a gecko tail), or the timer motor has burned out. It could also be loose wires, either on the time clock terminal board, or on the timer motor.
How do you turn off Pentair egg timer?
If you desire a different method of operation, programs 3 and 4 can be changed to Manual mode in the control menu. To operate in Egg Timer mode, press a program button and then press Start/Stop. The pump will run that setting for the set amount of time and then turn off.
How do I reset my Pentair?
Why does my Pentair pump keep stopping?
There are several reasons why your pump may randomly shut off—a behavior known as “pump tripping.” Most commonly, your pump may be operating at the wrong voltage, overheating, or simply failing to compete with your neighborhood’s electrical needs.
How do you reset the time on a Pentair pool pump?
How do I reset my Pentair Intelliflo variable speed pump?
To reset the pump to the factory default settings:
- Ensure that the pump is powered on and the green power LED is on.
- Press the Stop button to stop the pump.
- Press and hold all of the four Speed buttons simultaneously for four seconds. Power off the drive.
How do I reset my Pentair pool pump timer?
How to Set the Date/Time on the Pentair Intelliflo
- From the home screen, press the “Menu” button.
- Use the Up or Down Arrows to cycle to “Settings”
- Press “Select”
- Cycle to “Date/Time”
- Press Select.
- You will see the factory default Date, press “Select” again to edit.
How do I turn on Pentair Intelliflo variable speed pump?
How do I reset my pool pump?
Steps to Prime Your Pool Pump
- Turn off the pump. …
- Switch to recirculate. …
- Release air. …
- Clean out the pump basket. …
- Fill the pump basket. …
- Once the pump basket is filled and tightened, make sure the air release valve is open and turn the power to the pump on.
- Check the water flow to your pump.
How do I reset my Pentair Intelliflo pump password?
Make sure the pump has power, green LED is on. Make sure the pump is not running. Press and hold all of the four Speed buttons simultaneously for four (or more) seconds. Power off the pump, wait a few seconds, power it back on.
How do I set the schedule on my Pentair Intelliflo?
How do you set a pool pump timer?
How do I turn on my pool pump Pentair Easytouch?
What do you do when the power goes out and your pool freezes?
How do you program Pentair Intelliflo variable speed pool pump?
How do you clear an alarm on a Pentair pool pump?
Pressing the Reset button will clear the alarm once the fault condition has been resolved. In the event of a warning: The warning light ” ” will illuminate, but the pump will continue to run. The speed, flow or pressure limit that is causing the warning must be adjusted in order to correct the warning.
How do I restart my pool pump?
Steps to Prime Your Pool Pump
- Turn off the pump. …
- Switch to recirculate. …
- Release air. …
- Clean out the pump basket. …
- Fill the pump basket. …
- Once the pump basket is filled and tightened, make sure the air release valve is open and turn the power to the pump on.
- Check the water flow to your pump.
How do I reset my pool?
How do I reset my Pentair pool pump?
Why is my water pump not working after power outage?
Often when there is no water after a power outage it is due to the low-pressure switch. This is because the tank has to have a certain amount of pressure to keep the water levels where they need to be. When there is no power, the pressure drops and causes the pressure to drop. This then causes the water levels to drop.
Why won’t my pool pump come on?
When a pump doesn’t turn on or starts shutting off quickly after it’s started, it’s usually an electrical problem, which could mean loose connections, a bad capacitor or overloaded voltage. But it could also be a jammed motor.
How do I reset my Pentair Intelliflo?
To reset the pump to the factory default settings:
- Ensure that the pump is powered on and the green power LED is on.
- Press the Stop button to stop the pump.
- Press and hold all of the four Speed buttons simultaneously for four seconds. Power off the drive.
How do you unlock Pentair pool pump?
TO UNLOCK THE PUMP:
Press and hold the “1” and Quick Clean buttons for atleast 3 seconds. “Enter Loc Code” will scroll across the screen. 2. Use the “1”, “2”, “3” and Quick Clean buttons to enter your four-digit keypad lockout code.
How do I program my Intelliflo VSF pump?
What to do with pool if power goes out in winter?
How do you manually turn on a Pentair pool pump?
How do I reset my Pentair Intelliflo pool pump?
Why will my pool pump not turn on?
When a pump doesn’t turn on or starts shutting off quickly after it’s started, it’s usually an electrical problem, which could mean loose connections, a bad capacitor or overloaded voltage. But it could also be a jammed motor. All of these things are usually fairly simple fixes.
How do I manually turn my pool pump on?
How do you unlock Pentair Intelliflo?
Make sure the pump has power, green LED is on. Make sure the pump is not running. Press and hold all of the four Speed buttons simultaneously for four (or more) seconds. Power off the pump, wait a few seconds, power it back on.
How do you program a Pentair Intelliflo pool pump?
How does Pentair freeze protection work?
The system detects all devices that have Freeze Protection ON, and activates the device to stop the pipes from freezing. If freeze protec- tion is only applied to one body of water. Note: If the pool or spa is running a schedule or operated manually, this will override freeze protection.
Is there a reset button on a Pentair pool pump?
Why does my pool pump say over current?
Over Current
Indicated that the drive is overloaded or the motor has an electrical problem. The drive will restart 20 seconds after the over current condition clears.