If the Inspect Cell Light is the only LED light flashing, then you can reset it by simply holding down the diagnostic button for 3 seconds, then release. The Inspect Cell indicator will now reset and will later come back on after another 500 hours of use.
Also, how do I update my aqualogic software?
The USB memory stick must be plugged into the side of the Local Display behind the Dead Front of the OmniLogic. Next, you will be able to upgrade your firmware by going to OmniLogic’s Configuration Menu. With the new firmware, the OmniLogic will automatically start up again.
Simply so, how long does a Hayward pool pump last?
Your pool’s pump is the wet end of the operation, it houses the pump basket. Pumps should last through the initially installed motor and perhaps as many as two or three replacement motors, usually 10-12 years.
How do I reset my Hayward Aqua Rite 900?
How do I check my Hayward Salt Cell?
How do you troubleshoot a Hayward Aqua Rite?
Why is my salt cell light blinking?
If the “Inspect Cell” light flashes by itself it is an early indication that the salt generator needs a manual reset. Each cell is equipped with 500 operational hours and requires a manual reset once it expires. To reset the cell, hold down the “Diagnostic” button for 3-5 seconds.
What does check cell mean on pool pump?
If both the “check salt” and the “inspect cell” lights stay on, it most likely means that no chlorine is being produced at this time and your salt level fell below 2300 ppm. Both lights will also stay on if the controller is set to the wrong turbo cell type, or if the cell is unplugged.
Why is my check salt light flashing?
Why is my Salt Generator Flashing ‘Check Salt’ and ‘Inspect Cell’ Together? When both the “Check Salt” and “Inspect Cell” lights flash together, it is most likely an indicator that your salt level is below 2700 ppm. Keep in mind, your ideal salt level should be between 2800 ppm – 3200 ppm (parts per million).
How do I fix error code Hayward AO?
How do I know if my salt cell is working?
How do you know if your pool pump motor is bad?
Don’t Wait to Call for Swimming Pool Pump Replacement
- Age. Yes, the age of your pump is an early trouble sign. …
- Noise. Your pool pump should run quietly. …
- Power Trip. Has your pool pump motor started to trip your electric breaker box more and more frequently? …
- Swimming Pool Pump Motor Keeps Shutting Off. …
- Loss of Suction.
How do you clean the flame sensor on a Hayward pool heater?
How do I fix the error code on my Hayward pool heater?
TFP Guide
- Disconnect and then re- connect power to heater.
- Check for faulty wiring or connection. Inspect Display Interface Wiring. Ensure Display Interface Plug is securely attached to Control Module. If OK, proceed to step 2.
- Control Module and/or Display Interface Assembly are defective.
How do I unlock my Hayward configuration menu?
Unlock Configuration Menu To unlock the Configuration Menu, repeatedly press the Menu button until “Configuration Menu” is shown in the Menu Display. Press and hold the Menu Display for 5 seconds. Refer to your pool control’s manual to determine what options are offered within the Configuration Menu.
How do I reset my aqualogic check light?
Press the ‘Menu’ until, ‘Default Menu’ appears on the display. This menu is where the ‘Inspect Cell’ message is stored. Press the (>) key, repeatedly, until ‘Inspect Cell, Hold + to reset’ appears on the display.
How do you troubleshoot a Hayward chlorinator?
How do I reset my Hayward salt?
To reset, move the switch to ‘Off’ and then back to ‘Auto’. Wait for the relay to click (5 to 10 seconds). When the instant salt level is stable (and the negative sign still present), slide switch to ‘Super Chlorinate’ and back to ‘Auto’. It takes about 30 seconds for the unit to settle back on the default reading.
How do you troubleshoot a Hayward pool pump?
How to Troubleshoot a Hayward Pool Pump
- Step 1: Check the Hoses. Tighten all hose connections on the pump and filter. …
- Step 2: Inspect the Pressure Gauge. …
- Step 3: Check the Skimmer Basket. …
- Step 4: Remove Debris. …
- Step 5: Inspect the Impeller. …
- Step 6: Backwash the Filter. …
- Step 7: Replace the Sand or DE.