The first step is to check that the filter basket or filter bag is clean and not full causing lack of water flow. If the filters or bag is overly full this can compromise the robotic pool cleaner’s ability to efficiently navigate around the swimming pool.
In this way, how do I know when my dolphin pool cleaner is finished?
SHUT DOWN – After about 3 hours of operation, the Cleaner will shut down automatically as indicated by the 4 LEDs turning off. The Cleaner can remain in the pool until you are ready to pull it out. Many people run the cleaner at night and take it out in the morning.
Just so, why is there no suction in my pool vacuum?
Rule out the obvious causes of poor vacuum first. Make sure the water level in the pool is sufficient and air is not being sucked in through skimmer inlets. Add water to the pool to submerge the skimmers if necessary. Verify that the pump strainer basket and the skimmers are free of debris that may obstruct water flow.
How do I get my pool vacuum to work?
How long do Dolphin robotic pool cleaners last?
Generally, you can expect at least 5 years‘ service from your quality robotic pool cleaner. The more expensive units are generally better quality – you do get what you pay for.
How do you test a Maytronics power supply?
Testing the power supply
- Connect the tester to the power supply.
- Switch the power supply on.
- If the tester light is on, proceed to test the cable.
- If the tester light is off, check the power socket and AC cable. If they are working, then replace the power supply and proceed to test the cable.
Why won’t my dolphin pool cleaner climb walls?
My Dolphin Won’t Climb Walls / Gets Stuck
Clean filters: The Dolphin’s filters may be clogged and need to be cleaned. Make sure you clean these filters after each use. Do not allow filters to dry out before cleaning. Deeper cleaning of the filters is also highly encouraged and may be required occasionally.
Why is my automatic pool vacuum not moving?
If your robotic pool cleaner stops moving, check the power cord. It may not be plugged in properly or there may be a problem with the power supply. Check the power supply to make sure the indicator light is on. If it is and the pool cleaner is still not moving, then the problem lies with the cleaner.
How often should I run my dolphin pool cleaner?
Ideally, you need to run your robot pool cleaner daily or at least once a day if you’re always swimming in it. But if you don’t swim in it as much, run it at least once weekly or every two weeks. When you’re using a swimming pool cover all the time, you may wash your pool monthly.
How do I turn on my Maytronics pool cleaner?
TURN POWER ON – Press the ON/OFF switch on the Power Supply. The Cleaner will start to operate. Note: Four LEDs will light up in the corners of the switch indicating that the power is on.
How do you troubleshoot a dolphin pool cleaner?
Troubleshooting
- Check that the power supply cable is plugged properly into the power supply socket. Check power to the socket and reconnect Pool Cleaner.
- Ensure the power outlet is functioning properly and that it has not tripped the breaker in the fuse box.
- Turn the power supply off. …
- Unplug the power supply.
How do I adjust my dolphin pool cleaner?
To adjust the handle angle:
- Lay the handle down at an angle of 180º to the ground.
- Push the base of the arm into the body of the robot pool cleaner and slide it towards the rear of the robot pool cleaner until it clicks into the required position.
Why can’t you use an extension cord with a dolphin pool cleaner?
Do not use an extension cord. In a wet deck environment the risk of stray voltage while small is signicant.
Why does my pool cleaner stopped working?
Most likely, the key reason is a congested pool filter or skimmer basket, or a clog at the mouth of your pool cleaner. If you own a particularly powerful pool pump or your water-flow is really strong, your cleaner will probably move faster than normal.
How long is Maytronics warranty?
The Best Warranty in the Industry
Maytronics warrants that your Premier Dolphin pool cleaner will be free from defects in material and workmanship for 3 years. To prove how serious we are about delivering the best-in-class high performance robot, the Dolphin Premier is backed by the very best warranty in the industry.
How do I get air out of my pool pump?
How to Remove Air From a Pool Line
- Turn off power to the pool pump and pool heater. …
- Rotate the air relief valve located on top of the filter canister counterclockwise to open the valve.
- Close the skimmer valves and leave open the main drain valve.
Can I use an extension cord with my dolphin pool cleaner?
Dolphin Nautilus Automatic Robotic Pool Cleaner with Dual Filter Cartridges, Two Scrubbing Brushes… Dolphin does not recommend an extension cord.
Why is my pool vacuum losing suction?
Verify that the vacuum hose is firmly inserted into the inlet port at the skimmer; then inspect the hose for cracks or holes. The skimmer filter is dirty. Pull out the filter basket and check for debris that may be interfering with water flow to the pool pump. Air is getting into the pump through the pump cover.
Can you use a dolphin m200 on above ground pool?
Why is my dolphin pool cleaner floating?
ADMIN REPLY: The bag may be retaining air. Try turning the robot upside down in the water and see if air escapes.
Can I leave my dolphin pool cleaner in the pool?
Can you leave the Dolphin in the water? It is safe to leave your Dolphin cleaner in the water when not in use. However, (when adding chemicals to the pool) please remove the Dolphin until the proper chlorine and PH balance are obtained.
How do I test dolphin cable?
Grip the cable firmly and pull it out of the socket. 4. Using a multimeter set to continuity, check the continuity of each wire. If continuity is good, replace the plug, it can only go in one way, and tighten the hold down nut.
How do I keep my pool cleaner from getting stuck?
The easiest solution is a flow keeper valve. A flowkeeper valve is a valve that regulates the flow of water through the hose going to the cleaner. It can’t attach directly to the skimmer on the side of the pool so you’ll need an additional, short piece of hose.
How do I get my pool cleaner to work?
Where is the impeller on my dolphin pool cleaner?
How long do dolphin pool cleaners last?
Generally, you can expect at least 5 years‘ service from your quality robotic pool cleaner. The more expensive units are generally better quality – you do get what you pay for.
How long is cleaning cycle for dolphin s50?
Why is my pool cleaner not working?
Most likely, the key reason is a congested pool filter or skimmer basket, or a clog at the mouth of your pool cleaner. If you own a particularly powerful pool pump or your water-flow is really strong, your cleaner will probably move faster than normal.
Why is my robotic pool cleaner not moving?
If your robotic pool cleaner stops moving, check the power cord. It may not be plugged in properly or there may be a problem with the power supply. Check the power supply to make sure the indicator light is on. If it is and the pool cleaner is still not moving, then the problem lies with the cleaner.
How do you test a dolphin power supply?
Why does my pool cleaner get stuck?
If the suction is too strong, pushing the cleaner with a long pole virtually guarantees it will get stuck. Pulling the cleaner with a long pole isn’t as problematic, but it is still challenging. You just don’t have the control you have with a short pole.
Why is my pool robot not working?
If your robotic pool cleaner stops moving, check the power cord. It may not be plugged in properly or there may be a problem with the power supply. Check the power supply to make sure the indicator light is on. If it is and the pool cleaner is still not moving, then the problem lies with the cleaner.
Why is my aqua Critter not moving?
If your Pool Cleaner is not moving or is barely crawling it may be clogged with debris. This guide describes how to clear the the debris and check the operation of the Main Turbine that propels the pool cleaner.
Why is the pool cleaner not working?
When a suction cleaner is sluggish or slow, it’s usually a clogged pump basket or dirty filter that is to blame. Other problems include holes in the cleaner hose, sucking air into the hose, or the filter pump could be drawing in air, reducing water-flow volume.
Why does the creepy stop working?
The filter sand gets clogged
The most common cause for a Kreepy to stop working is clogged filter sand. This is easy to diagnose because whenever you backwash the pool filter, you’ll find that the Kreepy works like a bomb for 10 minutes. Then it gets sluggish and slows down or stops again.