Using the remote control
- Press the On/Off button once. The remote control will start in manual direction control mode.
- Use the direction control arrows (see right) to control the movement of the robot around the pool.
- To exit the manual direction control mode, press the Manual/Automatic select button once only.
In this manner, why is my automatic pool vacuum not moving?
If your robotic pool cleaner stops moving, check the power cord. It may not be plugged in properly or there may be a problem with the power supply. Check the power supply to make sure the indicator light is on. If it is and the pool cleaner is still not moving, then the problem lies with the cleaner.
Simply so, how do I reset my dolphin pool cleaner?
Turn the power supply OFF. Wait 30 seconds, then turn it back on. Pool Cleaner does not move / Red light on the power supply.
Why can’t you use an extension cord with a dolphin pool cleaner?
Do not use an extension cord. In a wet deck environment the risk of stray voltage while small is signicant.
How do I setup my dolphin pool cleaner?
Adjusting the handle angle
- Lay the handle down at an angle of 180º to the ground.
- Push the base of the arm into the body of the robot pool cleaner and slide it towards the rear of the robot pool cleaner until it clicks into the required position.
How do I know when my dolphin pool cleaner is finished?
SHUT DOWN – After about 3 hours of operation, the Cleaner will shut down automatically as indicated by the 4 LEDs turning off. The Cleaner can remain in the pool until you are ready to pull it out. Many people run the cleaner at night and take it out in the morning.
How long does a Maytronics Dolphin last?
Generally, you can expect at least 5 years‘ service from your quality robotic pool cleaner. The more expensive units are generally better quality – you do get what you pay for. If you keep your robotic pool cleaner in good condition, there is no reason it shouldn’t last much longer.
How do I reset my dolphin power supply?
Check that the power supply is plugged in and turned ON. Check that the power cable is securely connected all the way into the power supply. Turn the power supply OFF. Wait 30 seconds, then turn it back on.
How long is a cycle for a Maytronics dolphin?
Product Specifications
| S 300 | |
| Ideal pool length | Up to 12 m |
| Cleaning coverage | Floor, Walls & Waterline |
| Brushing | Brush + Active Scrubber |
| Cleaning cycle time | 1 or 2 hours |
How do you troubleshoot a Maytronics dolphin?
Troubleshooting
- Check that the power supply cable is plugged properly into the power supply socket. Check power to the socket and reconnect Pool Cleaner.
- Ensure the power outlet is functioning properly and that it has not tripped the breaker in the fuse box.
- Turn the power supply off. …
- Unplug the power supply.
Why won’t my dolphin pool cleaner climb walls?
My Dolphin Won’t Climb Walls / Gets Stuck
Clean filters: The Dolphin’s filters may be clogged and need to be cleaned. Make sure you clean these filters after each use. Do not allow filters to dry out before cleaning. Deeper cleaning of the filters is also highly encouraged and may be required occasionally.
How do I get my dolphin pool cleaner to work?
The Maytronics Dolphin Nautilus Robotic Cleaner is self-contained and fully automatic. Just drop it in your pool, turn it on and leave it for about 3 hours.
How do you test a Maytronics power supply?
Testing the power supply
- Connect the tester to the power supply.
- Switch the power supply on.
- If the tester light is on, proceed to test the cable.
- If the tester light is off, check the power socket and AC cable. If they are working, then replace the power supply and proceed to test the cable.
How do I set the timer on my dolphin pool cleaner?
How do I clean my dolphin m400?
How do you troubleshoot a Dolphin pool cleaner?
Troubleshooting
- Check that the power supply cable is plugged properly into the power supply socket. Check power to the socket and reconnect Pool Cleaner.
- Ensure the power outlet is functioning properly and that it has not tripped the breaker in the fuse box.
- Turn the power supply off. …
- Unplug the power supply.
Why does my dolphin keep getting stuck?
My Dolphin Won’t Climb Walls / Gets Stuck
Clean filters: The Dolphin’s filters may be clogged and need to be cleaned. Make sure you clean these filters after each use. Do not allow filters to dry out before cleaning. Deeper cleaning of the filters is also highly encouraged and may be required occasionally.
How long do Dolphin pool cleaners last?
You can expect the device to serve you for four or five years. It can even last up to eight years with the right upkeep. Although you can find cheaper models that do not offer the same lifespan but given the proper care, you can still expect them to run for at least three years.
How do I clean my Maytronics dolphin?
Why is my dolphin pool cleaner not moving?
If you can identify an obstruction you can remove the object and then run your Dolphin again. If the Dolphin starts and continues to operate as per normal the the obstruction was the cause of the robotic pool cleaner not moving.
How long is Maytronics warranty?
Maytronics warrants that your Premier Dolphin pool cleaner will be free from defects in material and workmanship for 3 years. To prove how serious we are about delivering the best-in-class high performance robot, the Dolphin Premier is backed by the very best warranty in the industry.
How do I turn on my Maytronics pool cleaner?
TURN POWER ON – Press the ON/OFF switch on the Power Supply. The Cleaner will start to operate. Note: Four LEDs will light up in the corners of the switch indicating that the power is on.
Can you swim while robotic pool cleaner?
You can swim while your bot cleans the pool, but it’s better not to. Swimming churns up the water. If the machine is in the water at the time, the current will buffet it, making it harder for it to complete its work. It’ll have to work harder to cover the same ground.
How do I program dolphin quantum?
Why is my dolphin pool cleaner doing wheelies?
What causes automatic pool cleaners to flip or do wheelies? The water level in a pool is one of the most common causes for this problem. When the water level is too high, the water line is very close to the coping. So when the cleaner starts to climb the wall, it hits the coping and flips on to its back.
Why is my pool cleaner not working?
When a suction cleaner is sluggish or slow, it’s usually a clogged pump basket or dirty filter that is to blame. Other problems include holes in the cleaner hose, sucking air into the hose, or the filter pump could be drawing in air, reducing water-flow volume.
How do I turn on dolphin pool cleaner?
TURN POWER ON – Press the ON/OFF switch on the Power Supply. The Cleaner will start to operate. Note: Four LEDs will light up in the corners of the switch indicating that the power is on.
How often should a pool be vacuumed?
In general, it’s a good idea to vacuum your pool once a week. You should also vacuum your swimming pool any time you notice large amounts of debris, dirt, or leaves on the floor of the pool (for example, your pool may need vacuuming after a heavy storm).
How often should I run my dolphin pool cleaner?
Ideally, you need to run your robot pool cleaner daily or at least once a day if you’re always swimming in it. But if you don’t swim in it as much, run it at least once weekly or every two weeks. When you’re using a swimming pool cover all the time, you may wash your pool monthly.
How do I pair my dolphin Bluetooth?
Make sure Bluetooth® is active on your smartphone and download and activate the MyDolphin™ app. Once downloaded, the app searches for and displays the serial number of the nearest Dolphin robot. Click on the Dolphin serial number displayed on your screen. Register by entering your email address and creating a password.
How do I connect my dolphin pool cleaner to Bluetooth?
Make sure Bluetooth® is active on your smartphone and download and activate the MyDolphin™ app. Once downloaded, the app searches for and displays the serial number of the nearest Dolphin robot. Click on the Dolphin serial number displayed on your screen. Register by entering your email address and creating a password.