Hayward Power-Flo Above Ground Pool Pump
It can easily be converted from horizontal to vertical to fit in almost any location and even includes an internal drain plug to make winterizing easy. This is the BEST pump for any above ground pool. Easy-to-use, easy to get parts, and just built like a tank!
Regarding this, what is the best water pump for an above ground pool?
1. Harris ProForce Above Ground Pool Pump – Best Overall. The Harris ProForce 1.5 HP Above Ground Pool Pump is the best above ground pool pump overall, as well as being the best 1.5 hp above ground pool pump. It’s made well and is extremely durable, so you should expect years of service out of this model.
Additionally, should pool pump be hot to touch?
Under normal operating conditions, the motor end of the pump is hot enough that you can barely touch it — but not searing hot. If you check your pool pump motor and find it is far too hot to be able to touch with your hand, that’s not good.
Which is better Pentair vs Hayward?
When it comes down to it, both pumps have their own strengths and weaknesses. The Hayward EcoStar has better energy efficiency and the Pentair IntelliFlo has a reputation for longevity with a proven track record. It’s a close battle between the two pumps and it really comes down to personal preference.
4.5 – 5.5 ft. 7 – 9 ft. 10.0 – 12.5 ft. 13.5 – 16.0 ft.
|Pipe Size||Max GPM|
Their heavy-duty, high-performance motor and airflow ventilation provide quieter, cooler, more efficient operation for virtually any pool or spa, while their exclusive service-ease design offers quick 4-bolt access to all internal components.
At River Pools, we used two speed pumps for years with great success. They are quite a bit more expensive to purchase than single speed pumps and last the same amount of time, which is typically 3-8 years. On average, a two-speed pump will save about 50%-70% on energy cost compared to a one-speed pump.
Round Above Ground Pool:
For pools up to 24 Ft Round, use a 1 HP pool pump. For pools over 24 Ft Round, we recommend using a 1.5 HP pool pump.
Sure you can, as long as the pump is at or below the pool water level, and you have a very small pool. If the pump is able to turnover all of the water in 8-10 hours, and is able to reach (but not exceed) the pool filter Design Flow Rate, the intended use of the pump (a/g or i/g) really doesn’t matter.
So to answer the question, yes, you can replace your 1hp pool pump with a 1.5hp pool pump, but only if your situation calls for it. If you’ve determined that your current pump is too small for your pool, then we’ll suggest replacing it with a larger ECO pump like the Water TechniX Pump Alpha ECO.
A professional electrician will be needed to disconnect the wiring before a pump can be removed. Once a new pump is installed, an electrician will again be necessary to reconnect the wires to the new pump. A do-it-yourself homeowner with basic mechanical aptitude can replace the pool pump in a relatively short time.
Signs You Need Pool Pump Replacement
- Rumbling Sounds. An excessively-vibrating pump motor can create these rumbling sounds. …
- Grinding or Screeching Sounds. …
- Blowing Bubbles and Spitting Water. …
- Old Age. …
- Get a New Pool Pump Now to Keep Enjoying Safe Water.
30,000 gallons ÷ 24 hours = 1250 gallons/hour.
Two-speed pool pumps are more energy-efficient than a single-speed pump, and work best on pools with water features. They run at two fixed speeds, high and low, and require a separate device such as an automation system to adjust between the two speeds.
The rule of thumb is generally 8 hours, although it could be anywhere from 6-12 hours, depending on your pool’s size. Each pool is unique, so to keep your pool pump efficient and effective, you need to figure out exactly what your pool’s turnover rate is.